PSI WallSleeves - GPT Industries
Installation using pipe clamp. Installation in formwork using pipe clamp. Do not use any seals in the sleeve until it is fi rmly fi xed and the surrounding material has set. The fi ller requires 24Hrs to harden after that time it may be set into the concrete. ... View This Document
ELEVATION CABLE FENCE PVC PIPE SLEEVE DETAIL BASE PLATE ...
-2 cable fence - top mount tue feb 06 14:22:17 2018 m:\\standards\\walls\\cable railing top mounted.man see pvc pipe sleeve pipe adjacent to base plate concrete coping finished grade at top of wall cast-in-place Ð"ø astm a307 headed bolt (full thread) or Ð"ø resin bonded anchor 1É"ø hole ... View Full Source
Chapter 7 - Underground Installation Of PE Piping
Chapter 7 Underground Installation of PE Piping 267 Figure 1 Pipe Trench Note: When groundwater levels are expected to reach above the pipe, the secondary initial backfill should be a continuation of the primary initial backfill in order to provide optimum pipe support. Minimum trench width will depend on site conditions and embedment materials. ... Read Content
Recommendations For AWWA C900 AWWA C905 - PVC Pipe For The ...
Tapping Sleeve & Valve Direct tapping is restricted to C900 pipe sizes 6” through 12 inch with pressure classes of DR 18 or DR 14. the video by Uni-Bell PVC Pipe Association entitled “Direct Tapping PVC Pipe” and ... Access Full Source
SECTION 220517-SLEEVES AND SLEEVE SEALS FOR PLUMBING PIPING ...
SECTION 220517-SLEEVES AND SLEEVE SEALS FOR PLUMBING PIPING PART 1-GENERAL D. PVC-Pipe Sleeves: ASTM D 1785, Schedule 40. sleeve for installing sleeve-seal system. 3. Concrete Slabs above Grade: a. Piping Smaller Than NPS 6: Galvanized-steel-pipe sleeves. ... Read Document
Floor Mount Sleeve - Capital Safety
Sleeve Material Sch. 40 Pipe/304 S.S. Sleeve Bearing Material PVC Pipe, ASTM-D-1785 Thrust Bearing Material High Density Polyethene Finish (Steel Sleeves) Zinc Plated Finish (Stainless Sleeves) Brush Blast Plating Specification ASTM Designation B633-85, Type III, SC2 Mounting Requirements(minimum): Concrete thickness: 6" in (150 mm) ... Fetch Doc
Confidence
Confidence Even Under Fire 3M™ Fire Protection Products Full Line Brochure. ShutterStock 916946 ShutterStock 3596804. Table of Superior adhesion — bonds to concrete, metals, wood, plastic and cable jacketing n Intumescent — expands when heated to seal around items exposed to fire n Low ... Read Content
Materials Catalog - Wsscwater.com
Materials catalog revised november 6, 2015 1 materials and services group . table of contents . mechanical joint to prestressed cyl. pipe (concrete) adaptor..26 diaper, pccp, lined concrete pipe (will fit astm d3034 pvc pipe ... Read More
Sure Sleeve - LSP
Sure-Sleeve Plastic Concrete Hole form Superior Design • Specially designed with dual 3˚ and 1˚ taper for easy release from concrete • Dual taper minimizes Fire-packing needed during pipe installation • Smooth exterior prevents sleeves from sticking to concrete • Internal supports prevent sleeves from cracking during rough concrete pours ... Fetch Document
Concrete Footing And Plumbing Pipe Sleeve - Building ...
Concrete Footing And Plumbing Pipe Sleeve - Building Foundations but I can't tell you how many times I was working around are on a concrete building foundation, only to end up with someone ... View Video
Speaker Wire - Wikipedia
Speaker wire is used to make the electrical connection between loudspeakers and audio amplifiers. Modern speaker wire consists of two or more electrical conductors individually insulated by plastic (such as PVC , PE or Teflon ) or, less commonly, rubber . ... Read Article
12. Allowable Joint Deflections. - Wsscwater.com
First consider using concrete thrust blocking before specifying restrained joints, Section 12. Allowable Joint Deflections WATER DESIGN GUIDELINES 2008 W-12.5 e) Wedge action-restraining glands on PVC Push-on pipe. WSSC for PVC pipe sizes 12-inch and smaller diameter. TABLE "5.4" ... Get Doc
Pipe, or ABS or PVC Solid Plastic Pipe, or Corrugated High Density Polyethylene Pipe (HDPE), as specified under Section 1 of this specification, or as otherwise noted. Stubs twelve inches (12") and larger shall be ASTM C76 Class IV Reinforced Concrete Pipe or as otherwise noted. ... View Document
20 20 13 - Pipe Sleeves, Supports, And Anchors For Facility ...
PIPE SLEEVES, SUPPORTS, AND ANCHORS FOR FACILITY SERVICES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe sleeve B. Pipe hangers, supports, and guides C. Anchors and anchorage devices D. Seismic requirements 1.02 RELATED SECTIONS A. Miscellaneous metalwork is specified in Section 05 50 00 - Metal Fabrications. Coordinate the ... Fetch Document
Ecoflex Wall Penetration Systems: An Efficient, Sustainable ...
Ecoflex® Wall Penetration Systems: An efficient, sustainable solution for concrete wall, cut the Wall sleeve in the field for Compression Wall seal is a mechanical expansion device installed over the pipe and into the Wall sleeve to provide a watertight seal . ... Read Full Source
Page 2 Www.metraflex
The Metraflex MetraSeal quickly fills the space around any round pipe, including concrete, steel, plastic, cast weight steel or PVC wall sleeve that was used or the diameter of the core bit drilled hole. Standard Weight Steel or PVC Pipe Sleeve* Cast or core bit drilled hole* Sleeve ... Read Full Source
Pipe Penetration Seals - PROCO
Pipe Penetration Seals • Wall Sleeves • Precast Concrete • Valve Pits Table 1 Standard Weight Steel or PVC Pipe Sleeve1 Cast or Core Bit Drilled Hole1 NOMINAL PIPE SIZE (Inches) ACTUAL PIPE O.D. (Inches) SLEEVE NOMINAL ... Fetch Document
STANDARD DETAILS FOR WATER MAIN INSTALLATIONS
Proposed water main sleeve proposed water buffalo box pipe break symbol north arrow handicapped symbol proposed water main inspection manhole if transition sleeve req’d provide concrete thrust block on hydrant note: water table must be below bottom of drain sump. ... Fetch Here
Floodgate - Wikipedia
Valves used in floodgate applications have a variety of design requirements and are usually located at the base of dams. They are a round pipe section with an adjustable sleeve gate and cone at the discharge end. Water flows through an annular gap between the pipe and cone when it is ... Read Article
No comments:
Post a Comment